| Pages: [1] :: one page |
|
|
| Author |
Thread Statistics | Show CCP posts - 0 post(s) |
Zilexan
   |
Posted - 2008.06.29 20:24:00 -
[1]
I have just recently finished training for this ship but i have been unable to find a setup for the ship i really liked.
My goals with it was to ofc fit a covert ops cloak, a recon prob launcher and a MwD. but after fitting that i hardly got any Pg/Cpu left for anything (i belive i even had to use a fitting moduel to get the PG needed) i currently only have covert ops IV and im not planning on training lvl V.
So please if you have any setups please post them. this is only for scounting and locating targets in pvp not exploration sites ect. if i done that ill use another ship for clearing the site
|
AstroPhobic
Minmatar
|
Posted - 2008.06.29 20:46:00 -
[2]
Um... unless your fitting skills are pretty poor, it's not hard to fit. CPU can be tight, so you have to mix up your mids a bit.
Off the top of my head:
Recon Probe/Covert Cloak/offline cyno button or whatever you want
MWD/Cap rechcarges/Warp Disruptor/EW
Nanos/Inertia/ODs/CPR
2 scan time rigs |
RuleoftheBone
Minmatar
Celestial Apocalypse
The Requiem
|
Posted - 2008.06.29 22:29:00 -
[3]
You'll want Covops V:
[Cheetah, Recon ]
Overdrive Injector System II
Overdrive Injector System II
Inertia Stabilizers II
1MN Afterburner II
Warp Disruptor II
Phased Muon Sensor Disruptor I, Scan Resolution Dampening
Phased Muon Sensor Disruptor I, Scan Resolution Dampening
Covert Ops Cloaking Device II
Recon Probe Launcher I, Snoop Scanner Probe I
Offline salvager
Gravity Capacitor Upgrade I
Gravity Capacitor Upgrade I
You can swap out for an MWD...but its a bugger to fit anything remotely like the above. Depends on what you are doing with it. Why do you think you need an MWD?
|
Hannobaal
Gallente
Federal Defence Union
|
Posted - 2008.06.30 00:38:00 -
[4]
I use an afterburner and 3 overdrive injectors on mine. It works well enough for getting through bubble camps. |
Qui Shon
|
Posted - 2008.06.30 08:22:00 -
[5]
 Originally by: AstroPhobic
Um... unless your fitting skills are pretty poor, it's not hard to fit. CPU can be tight, so you have to mix up your mids a bit.
Off the top of my head:
Recon Probe/Covert Cloak/offline cyno button or whatever you want
MWD/Cap rechcarges/Warp Disruptor/EW
Nanos/Inertia/ODs/CPR
2 scan time rigs
Like the OP hints at, the above doesn't fit. Wthout a pg mod, you have 0.75pg left over after named mwd + highslots.
I mainly use it for PvE scanning, or just for having a look around 0.0, to examine camps and such. Have 2x beta PDS + nano, named mwd + shield booster, but the mids are mainly there for emptying the capacitor to limit warp range, the pds to regain capacitor quicker. Not that I've had any great success making precision warps with that technique, it just warps too fast :-/
Camps, bubbles, massive "graveyards" i.e. lots of corpses/junk on gates, so far none of that has presented any problems. Always just mwd + cloak to get out, or cloaked slowboating to get in, worked okay so far. Just a blink and I'm speeding away at 2000-2500m/s. Have to try the 2xod+nano with AB technique soon.
Don't know what I'd fit in mids, that could be of use. Though I like RotB's setup, if I were to ever use it for gang work. |
Hoshi
Deep Core Mining Inc.
|
Posted - 2008.06.30 08:29:00 -
[6]
If you prefer MWD over afterburner (like me) you can go with this:
High:
1x Recon Probe Launcher I
1x Covert Ops Cloaking Device II
1x Salvager I (offline)
Mid:
1x Catalyzed Cold-Gas I Arcjet Thrusters
1x Small Capacitor Battery II
1x Warp Disruptor II
1x Phased Muon Sensor Disruptor I
Low:
1x Micro Auxiliary Power Core I
1x Co-Processor II
1x Overdrive Injector System II
Rigs:
Your choice, I prefer Auxiliary Thrusters as I already have sub 30sec scan time.
If you switch to a named Micro Auxiliary Power Core you can switch to a t2 mwd. |
|
|
| |
|
| Pages: [1] :: one page |
| First page | Previous page | Next page | Last page |