Pages: 1 :: [one page] |
|
Author |
Thread Statistics | Show CCP posts - 0 post(s) |
Pasus
|
Posted - 2009.12.16 13:52:00 -
[1]
Hello All
Sry. english is not my best.
I have tryed this on a Proteus:
Low 1600mm Reinforced Rolled Tungsten Plates I Imperial Navy Energized Adaptive Nano Membrane Imperial Navy Energized Adaptive Nano Membrane Imperial Navy Energized Reflective Membrane Imperial Navy Energized Reactive Membrane Damage Control II Medium Armor Repairer II
Rigs Medium Trimark Armor Pump II Medium Trimark Armor Pump II Medium Trimark Armor Pump II
Got full Slave set and a ZET4000 and ZET5000
Using EFT that should give me 226.068 total hitpoints without using the dmg-II
But when I undocked the fitting 'tells me' that I only have 140.685 total hitpoints without using the dmg-II
All other stats are the same, and I have updated EFT with my skills.
Can't understand the difrent ??? Anyone, that can tell me why ??????
Thx
/Pasus
|
AterraX
Caldari
|
Posted - 2009.12.16 14:01:00 -
[2]
Factor in the cap to amour hitpoint conversion rate...that should do the trick.
|
RedClaws
Amarr Dragon's Rage Green Alliance
|
Posted - 2009.12.16 14:17:00 -
[3]
IIRC the ingame one doesn't take into account resistances. It's just armor HP, shield HP and structure HP into one value.
|
Tippia
Reikoku IT Alliance
|
Posted - 2009.12.16 14:17:00 -
[4]
Edited by: Tippia on 16/12/2009 14:18:59 EFT calculates its EHP using whichever damage type distribution you have set it to use. The in-game fitting screen calculates its EHP using your lowest resist against each layer of HP. Also, it uses you current stats, so if you're, say, in the hangar, none of the active modules are included (because, obviously, they're not active at the moment and therefore don't count). ùùù ôIf you're not willing to fight for what you have in ≡v≡à you don't deserve it, and you will lose it.ö ù Karath Piki |
Ulwithy Arillious
|
Posted - 2009.12.16 15:24:00 -
[5]
Originally by: Tippia Edited by: Tippia on 16/12/2009 14:18:59 EFT calculates its EHP using whichever damage type distribution you have set it to use. The in-game fitting screen calculates its EHP using your lowest resist against each layer of HP. Also, it uses you current stats, so if you're, say, in the hangar, none of the active modules are included (because, obviously, they're not active at the moment and therefore don't count).
No kidding... I've wondered about the weird EHP numbers I see. Thanks!
|
Sokratesz
|
Posted - 2009.12.17 10:30:00 -
[6]
Even still, taking all that into account, I find that the numbers in-game and in EFT can differ quite a bit.
When will TQ hit the 100K PCU mark? Place a bet! |
Kazuo Ishiguro
House of Marbles
|
Posted - 2009.12.17 10:35:00 -
[7]
Originally by: Sokratesz Even still, taking all that into account, I find that the numbers in-game and in EFT can differ quite a bit.
Example please? --- 34.4:1 mineral compression |
Sokratesz
|
Posted - 2009.12.17 11:30:00 -
[8]
Originally by: Kazuo Ishiguro
Originally by: Sokratesz Even still, taking all that into account, I find that the numbers in-game and in EFT can differ quite a bit.
Example please?
On my leviathan the lowest resist EFT HP was a lot higher than what in-game showed. That was before dominion though.
When will TQ hit the 100K PCU mark? Place a bet! |
NoNah
|
Posted - 2009.12.17 11:36:00 -
[9]
Originally by: Sokratesz
Originally by: Kazuo Ishiguro
Originally by: Sokratesz Even still, taking all that into account, I find that the numbers in-game and in EFT can differ quite a bit.
Example please?
On my leviathan the lowest resist EFT HP was a lot higher than what in-game showed. That was before dominion though.
Does that mean you have 3 active non-explosive hardeners and looked at it while all active and such?
I've only really tried it at some point, and then it was spot on. Parrots, commence!
Postcount: 322150
|
Sokratesz
|
Posted - 2009.12.17 11:53:00 -
[10]
Errr?
Yeah I have 4x active hardeners and they were all active at the time and lowest EHP was still EM.
When will TQ hit the 100K PCU mark? Place a bet! |
|
NoNah
|
Posted - 2009.12.17 12:38:00 -
[11]
Originally by: Sokratesz Errr?
Yeah I have 4x active hardeners and they were all active at the time and lowest EHP was still EM.
See that's the thing. EM is most likely not the lowest resistance in armor. Which should put them at a difference of 340k ehp. Parrots, commence!
Postcount: 356023
|
|
|
|
Pages: 1 :: [one page] |