| Pages: [1] :: one page |
|
|
| Author |
Thread Statistics | Show CCP posts - 0 post(s) |
Lledrith
Minmatar
Ex Caminus
   |
Posted - 2011.01.29 23:57:00 -
[1]
Soo like a good player i was looking for any reason as to why is not giving the amount set from the Extractors i have found the problem..... and is no funny.
in the nexts screenshots you will find that CCP has change the Clickfest from the pass Planet Interaction to its newest version.
in this screenshot you see that A is giving you a routed amount and B a total amount not being routed.
Link
this is what happen when route B that amount is change to a preset shown in arrow A of this image (Preset CAN'T BE CHANGE)
Link
once you route that total amount it add 2 routed in the products section and 1 total amount not being routed again. guess what....
Link
this is what happen when a Dev doesnt test their products and us the players have to do their job. the total amount only do a small deduction of the preset instead of routing the HOLE THING.
Link
Now you have to actually route each extraction to the ECU. your not loosing the planetary materials is more that you have to Reroute them each and EVERYTIME until you have perform the last batch.
Are %&$# you Kidding me.
|
Ephraim Glass
|
Posted - 2011.01.30 00:06:00 -
[2]
Under the old system, if an extractor overran the input capacity of the factory you were sending its outputs to, you lose the outputs then too. Here's the solution: Route the extractor through a silo of some sort (I use my command center) and then have the command center route the P0 materials to your factories. What I'm finding is that over the course of 4 days or so, I build up an excess in the first day or so and then work it down over the next 2-3 days.
|
Kasugano
|
Posted - 2011.01.30 00:37:00 -
[3]
route from the extraction thingy to storage. from storage to the processor. you only have to route once to storage, and once from storage to the processor.
Your doing it wrong. Routing straight from extractors into processors was the wrong way to do it in the old system as well. Use your command center, a launch pad, or a silo, and route through that.
|
Zaerlorth Maelkor
The Maverick Navy
IT Alliance
|
Posted - 2011.01.30 01:22:00 -
[4]
 Originally by: Kasugano
Your doing it wrong. Routing straight from extractors into processors was the wrong way to do it in the old system as well. Use your command center, a launch pad, or a silo, and route through that.
/thread
However, you might want to consider a few things, first of all; I now have one of those annoying sigs.
second; you should probably move on to some more interesting things than reading this sig.
|
lushn
|
Posted - 2011.01.30 01:26:00 -
[5]
Always send raw materials to launch pad, command center or silo first. then reroute to processor. DOnt send directly to processor. I was a mistake I ve done when I first started to do PI. Usually your process amount less then extraction. it should be , Unless You built many processor, more than you need.
P0 raw material will be collected in silo. This will be kinda a buffer if you missed cycle. ALso It will help to understand if u are in balance. You can swith production on one Processor or add extra proc or make changes on head numbers.
Also do same for P1 material. Collect in silo forst then reroute to adv process
|
Clown Pron
|
Posted - 2011.01.30 03:07:00 -
[6]
First, train some common sense and then read some guide.
|
|
|
| |
|
| Pages: [1] :: one page |
| First page | Previous page | Next page | Last page |