Pages: 1 2 3 4 [5] :: one page |
|
Author |
Thread Statistics | Show CCP posts - 0 post(s) |
Batelle
HOMELESS. Atrum Tempestas Foedus
|
Posted - 2008.03.17 19:18:00 -
[121]
rigging a brutix with ccc's is a complete waste. Damage controls are only useful after you have 3-4 hardeners already. You need the third hardener. EC-P8R... You will never find a more wretched hive of scum and villainy. |
Richard Third
The Scope
|
Posted - 2008.03.17 19:48:00 -
[122]
Edited by: Richard Third on 17/03/2008 19:50:01 Brutix is a nice ship. Nice until you get a real hard level 3 mission and you can't complete it w/o warping back to the station...
Anyhow... Mids should be
- cap recharger tech 2
- target painter
For blaster setups you will need an afterburner. For rail setups you will need a stasis webifier and a tracking computer.... Optical tracking computer is the best. I prefer the rail setups because I don't like spending my minutes chasing cruisers around a deadspace.
Nobody mentioned engergized specific membranes? They are the best for the armor tank if you don't want to waste cap on hardeners.
Dual 150 Railguns are fine for a brutix, but you will have to be real close to use antimatter ammo w/ them. I wouldn't put a Nosferatu on a PVE brutix I don't think it would help as much as another gun.
Even better for level 3's is a Hyperion with 7+ 250mm Rails.... Do any level 3 in less than an hour with fewer Iridium M charges :)
-- You can't do that with a Planet. |
Avtambaram
C0RSAIRS
|
Posted - 2008.03.18 16:48:00 -
[123]
Edited by: Avtambaram on 18/03/2008 16:55:30 Edited by: Avtambaram on 18/03/2008 16:54:06 Edited by: Avtambaram on 18/03/2008 16:53:10
Originally by: Batelle rigging a brutix with ccc's is a complete waste. Damage controls are only useful after you have 3-4 hardeners already. You need the third hardener.
I need the Tech 1 ccc's to sustain the single tech 2 armor rep tank. Also, it would be almost impossible to run a dual armor rep tech 2 tank (long enough to be effective) without the three ccc rigs.
A third hardener for the primary damage type dealth adds approximately another 10% resist to that damage type. But if you're taking heavy missile, armor starts going down faster than the single rep can handle. There again, the dual rep is the best way out in my mind.
About the damage control tech 2; it is my insurance policy. without it, the 6000 structure hp are naked to enemy damage. But with it, structure has 60% resists to all damage types. Also, the damage control tech 2 give 15% reists to armor, and 12.5% resists to shields, for all damage types. I would much rather fit the damage control than not.
Out of curiosity, what other rigs, if not ccc's, would you rather fit on a brutix?
To Richard, I will try out your recommendations, particularly the target painter and the tracking computer. Energized membranes I haven't looked into yet. Also, I still need to train Hull Upgrades to lvl 5. I am fond of active hardeners as for my setup, they are very easy to perma run, and they add significantly to resists on a ship.
|
Shady Fark
|
Posted - 2008.04.10 06:13:00 -
[124]
IF you want to fit expensive rigs to a tier 1 BC... push its bonuses. Aux nano rigs are much cheaper than CCC's and will boost the rep amount. Might get it high enough for you to only need to pulse it and save the cap and an extra slot. Check EFT with your skills to see. Dont go the speed route or it will eat your cap like no tomorrow.
BC 5 3x Aux Nano and 1 MAR1 and I can do 440 per 8 sec BC 5 3x Aux Nano and 1 MAR2 and I can do 587... So check EFT with your skills. I don't do enough missions to know if that's good enough for lvl 3's etc but it certainly works in PVP =)
|
Miandondon
|
Posted - 2008.04.19 06:05:00 -
[125]
Originally by: Batelle rigging a brutix with ccc's is a complete waste. Damage controls are only useful after you have 3-4 hardeners already. You need the third hardener.
Damage controls are not stack-nerfed, omni-tank and harden shield, armor and hull. At Type II, the overall bonuses are worth it even before the third hardener.
A nano-pump or two is good instead of all CCCs. But nano-pumps are stack-nerfed, unlike CCCs. Also, CCCs give you more cap to run other stuff, so they are a more flexible offensive tool.
|
lyrenna
Caldari Soliders Of Eve
|
Posted - 2008.04.19 09:54:00 -
[126]
best brutix pve setup is buying a myrmidon
|
Txakoli
|
Posted - 2008.05.13 07:26:00 -
[127]
This is what i use and it seems to work.
Hi: 5* 250mm comp. rails (Lead) 2* 125mm rail II (AM)
Med: AB II 3* Cap Recharger II
Low: Med armor rep II 3* active hardeners Energized adaptive nano mambrane II
Please comment.
|
Darth Felin
|
Posted - 2008.05.13 10:45:00 -
[128]
Originally by: Txakoli This is what i use and it seems to work.
Hi: 5* 250mm comp. rails (Lead) 2* 125mm rail II (AM)
Med: AB II 3* Cap Recharger II
Low: Med armor rep II 3* active hardeners Energized adaptive nano mambrane II
Please comment.
Your tank is not enough for some of the harder lvl 3 missions. And it is bad idea to use EANM - it will be third hardener for primary damage type stacking will be painful. It is better to use second active hardener for secondary damage type instead. And btw Brutix don't have bonus for small rails.
|
|
|
|
Pages: 1 2 3 4 [5] :: one page |
First page | Previous page | Next page | Last page |